Jet-tools J-3410-2 Uživatelský manuál

Operating Instructions and Parts Manual7x12 Cut-off Band SawModels: J-3410, J-3410-2WALTER MEIER (Manufacturing), Inc.427 New Sanford RoadLaVergne, Te

10Controlling the cut:Hydraulic feed controlThe weight of the saw arm typically provides all ofthe force needed to move the saw blade through theworkp

11Changing blade speedsThe ModelsJ-3410 and J-3410-2 are 4-speed cut-off saws. The different speeds are obtained by changingthe position of the driv

12Right angle cuts --single pieces of stock1. Raise the saw arm to its full up, open position.2. Pull up on the quick release handle on the locking

13Figure 8: Placing workpieces in the vise

14MaintenanceReplacing blades1. Disconnect the saw from its electrical power source toprevent accidental start-ups.2. Raise the saw arm to its full

15Blade alignment adjustmentsThe blade can suffer from several out-of-adjustmentconditions. These conditions are shown in Figure 10.Figure 11: Nomenc

16Replacing blade guideand support componentsAll component parts are secured with nuts, bolts,washers, or snap rings. To remove and replace anycompon

17Adjusting blade vertical:The blade guide bearing seat can rotate as needed tomake the blade vertical to the saw table. Follow theseinstructions.1.

18Adjusting guide bearingsThere are eight side blade guide/support bearings.These bearings are installed in the bearing seat, and theseat is attached

19Replacing the drive wheel1. Complete steps 1 through 6 in Replacing blades.2. Remove the snap ring which secures the lower wheelto the gearbox out

Warranty and ServiceWalter Meier (Manufacturing), Inc., warrants every product it sells. If one of our tools needs service or repair, one of ourAuthor

20Servicing the hydrauliccontrol cylinderOver a long period of service the hydraulic controlcylinder may need replacement of its internal seals. Uset

21Machine Set-upThe saw delivered to you has been adjusted at thefactory. A number of test pieces have been cut using thesaw to verify the accuracy o

22Installing the coolant kit1. Install the baffle in the tank so the pump is held at oneend of the tank.2. Put the tank and pump assembly in the fla

23Troubleshooting1. Use more pressure to tighten vise.2. Check stationary jaw pivot and lock bolts for tightness.3. Check quick release handle nut

241. Observe chip formation to be sure cutting is efficient.1. Adjust guide bearings according to instruction in thismanual.1. Increase blade tensi

25Replacement PartsThis section provides exploded view illustrations that show the replacement parts for the Model J-3410 andJ-3410-2, 7" x 12&q

26Exploded View - Saw Head

2750 5710551 Bearing pin 251 5710561 Eccentric shaft assy. 251-1 5517504 Center shaft assy. 252 5710571 Brush 153 5710581 Hex nut 3/8x24 454A 5710591

28Exploded View - Saw Base

29Parts List - Saw BaseRef.no.Part no.DescriptionQty.Ref.no.Part no.DescriptionQty.19 5710211 Spring washer 3/8 220 5710221 HH screw 5/16x3/4 820-1 55

3Table of ContentsCover Page ...

30Parts List - Hydraulic CylinderRef.no.Part no.DescriptionQty.1 5517547 Dust cover 12 5517548 Retaining ring 23 5517549 Oil-seal 14 5517550 Oil-pisto

31

32WALTER MEIER (Manufacturing), Inc.427 New Sanford RoadLaVergne, Tennessee 37086Ph: 800-274-6848www.waltermeier.com

4Cutting capacityBlade speedsBlade driveMotorBlade guidesBlade sizeBlade wheelsDimensions (LWH)WeightWet cutting packageGeneralSpecificationsThe JET M

51. Always wear protective eye wear when operatingmachinery. Eye wear shall be impact resistant, protectivesafety glasses with side shields which co

6close as possible to the work piece.9. Always wear protective eye wear whenoperating, servicing or adjusting machinery. Eyewearshall be impact resis

7Operating InstructionsUsing the viseThe vise on the saw table has two jaws. The jawclosest to the right hand side of the table is the stationaryjaw.

8eventually catch the thrust shaft and allow you to open orclose the locking jaw at its new lead screw position.When you slide the jaw to a new positi

9Adjusting stationary jaw forhigh accuracy angle cutting:1. Raise the saw arm to full height and lock it in positionwith the shut-off valve.2. Open