Jet-tools 708358 Uživatelský manuál Strana 1

Operating Instructions and Parts Manual Wood Lathe Model: JWL-1442VS WMH Tool Group 2420 Vantage Drive Elgin, Ill

10Stand Legs (optional accessory) 1. At this point the headstock, tailstock and tool rest should be removed. With help from another person, lift th

11G. Headstock Spindle Lock: (G, Fig. 5) Push in pin to keep the spindle from turning. CAUTION! Never press the headstock spindle lock while the sp

12N. Tool Rest Body Lock Handle: (N, Fig. 8) Locks the tool rest body in position. Unlock handle to position the tool rest in any location along lat

13Lathe Tools (continued) Skew — used to make vees, beads, etc., see Figure 11. Square Scraper — used for diameter scraping and featureless scrapin

14Stock Selection Stock for spindles should be straight grained and free of checks, cracks, knots and other defects. It should be cut 1/8" to 1

15Beads 1. Place the parting tool on the tool rest and move the tool forward to make the full bevel of the tool contact the workpiece. Gently raise

16Sanding and Finishing Leaving clean cuts will reduce the amount of sanding required. Begin with a fine sandpaper (120 grit or finer). Coarser sand

17Face Plate or Chuck While faceplates are the simplest, most reliable method of holding a block of wood for turning, chucks can also be used. A chu

18To Shape the Outside of a Bowl 1. Odd shaped burls, crotches and other irregular shaped blanks require special preparation before mounting in a ch

19To Shape the Interior of a Bowl 1. Stop the lathe and move the tailstock away. Remove the center from the tailstock to prevent bumping it with yo

2This manual has been prepared for the owner and operators of a JET JWL-1442VS Wood Lathe. Its purpose, aside from machine operation, is to promote s

20Adjusting the Clamping Mechanism The clamps are pre-set at the factory and should not need any adjustment. However, if adjustment is needed, remov

21 Troubleshooting Problem Possible Cause Solution Excessive Vibration. 1. Workpiece warped, out of round, has major flaw, improperly prepared fo

22Bed Assembly

23Bed Assembly Index Part No. No. Description Size Qty. 1...JWL1442-201... Bed...

24Headstock Assembly

25Headstock Assembly Index Part No. No. Description Size Qty. 1...JWL1442-101... Spur Center...

26Headstock Assembly (continued) Index Part No. No. Description Size Qty. 43...BB-6006LLB... Ball Bearing...

27Stand Assembly (optional accessory) Stand Assembly Index Part No. No. Description Size Qty. 3...JWL1642-203... St

28JWL-1442VS Safety Guard (optional accessory) Safety Guard 1. Mount the guard bracket (A) to the headstock with two 3/8” flat washers, two 3/8”

29Safety Guard Assembly Safety Guard Assembly Index Part No. No. Description Size Qty. 1...JWL1442-301... Guard Bra

3 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. This wood lathe is designed and intended for use b

30Tool Basket 1. Mount the bracket (A, Fig. 1) to the inside of the lathe leg with two 5/16”-18 x 1-1/2” Hex Socket Cap Screws, four 5/16” flat was

31Wiring Diagram

32 WMH Tool Group 2420 Vantage Drive Elgin, IL 60123 Phone: 800-274-6848 www.wmhtoolgroup.com

4 SPEED RECOMMENDATIONS Diameter of Work Roughing RPM General Cutting RPM Finishing RPMUnder 2" 1500 3000 30002 to 4" 600 1500 23004 to

5Grounding Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or break

230 Volt Operation If 230V, single-phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the powe

7Introduction This manual is provided by JET covering the safe operation and maintenance procedures for a Model JWL-1442VS Wood Lathe. This manual c

8Specifications JWL-1442VS Stock Number.......

9 WARNING Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury