Jet-tools J-7040 Uživatelský manuál

Operating Instructions and Parts Manual 10” x 16” Horizontal Band Saw Models J-7020, J-7040 WALTER MEIER (Manufacturing) Inc. 427 New Sanford R

108.5 Evaluating cutting efficiency Is the blade cutting efficiently? The best way to determine this is to observe the chips formed by the cutting

11block. Slide the block until the pointer on the block is aligned with desired angle (see Figure 7). Tighten the locking handle to set the angle. 3.

125. Start the motor and allow the saw to come up to speed. 6. Slowly set the saw down onto the workpiece. Adjust cutting speed with feed rate con

13screw in the other direction so the blade stops, then moves slowly toward the shoulder. Keep fingers clear of blade and wheel to avoid injury. 8.

14 Figure 13: Blade-to-bearing orientation 4. Position the bearing by turning the bushing. Set the clearance at approximately 0.001 inch. (The bla

153. Clean up accumulated saw cuttings after use. Make sure the lead screw is kept free of saw cuttings and other material that would cause damage.

1612.5 Replacing drive motor 1. Disconnect the motor from all electrical power. Unplug the motor if it is plugged into a socket. Shut off the powe

1712.10 Replacing carbide blade guide Refer to Figure 17. 1. Remove the cap screw and remove the carbide guide. Discard the carbide guide. 2. In

1813.0 Troubleshooting the J-7020/7040 Band Saws Symptom Possible Cause Correction Excessive blade breakage Material loose in vise. Clamp work se

19Symptom Possible Cause Correction Unusual wear on side/back of blade Blade guides worn Replace blade guides. Blade guide bearings not adjusted. A

21.0 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of ou

2014.1.1 Base (J-7020/7040) – Exploded View

2114.1.2 Base (J-7020/7040) – Parts List Index No Part No Description Size Qty 1 ... J-5712251 ...Foot, Left...

22Index No Part No Description Size Qty 36 ... 5712641 ...Washer ...

23 Index No Part No Description Size Qty 77 ... J-5713091 ...Protractor Seat ...

2414.2.1 Head (J-7020/7040) – Exploded View

2514.2.2 Head (J-7020/7040) – Parts List Index No Part No Description Size Qty 79 ... 5713381 ...Screw ...

26Index No Part No Description Size Qty 111-1 ... 5519682 ...Label, Motor...1.5HP, 115/230 3

27Index No Part No Description Size Qty 152 ... 5714161 ...Screw ...

2815.0 Electrical Connections 15.1 Electrical Connections – single phase only (model J-7020) Figure 20: Model J-7020 wiring diagram Figure

2915.2 Electrical Connections – three phase only (model J-7040) Figure 22: Model J-7040 wiring diagram Figure 23: Connection diagram for 3PH m

32.0 Table of contents Section Page 1.0 Warranty and Service ...

30 This page intentionally left blank.

31This page intentionally left blank.

32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jetttool

3.0 Safety Warnings General Cautions - Misuse of this machine can cause serious injury. - For safety, the machine must be set up, used and servi

518. Keep hands in sight and clear of all moving parts and cutting surfaces. 19. All visitors should be kept at a safe distance from the work area.

64.0 About this machine and manual The JET Models J-7020 and J-7040 Horizontal Cut-Off Band Saws are ruggedly built, precision-oriented machines des

7Speeds and capacities: Blade speed ... variable 100-350 fpm ... variable 100-350 fpm ... variable

86.0 Machine setup The saw delivered to you has been adjusted at the factory. A number of test pieces have been cut using the saw to verify the accu

9knob is turned counterclockwise. Speed decreases when the knob is turned clockwise. 2. A placard on the drive belt guard provides recommended speed